Description
Sensepeek PCBITE-4005 – 4x SP10 probes with test wires
These four handsfree SP10 probes expand your existing PCBite setup. Position each probe on the signals you need and monitor them with your logic analyzer, multimeter or debug adapter while keeping both hands free.
Place the spring-loaded needle on any test point in the signal path and release. The flexible arm holds the needle in position, while the N52 neodymium magnet in the base keeps the probe locked to the base plate. No soldered wires and no fixtures.
The 2.54 mm (0.100 in) dual pin header accepts two cables at the same time, enabling simultaneous power and measurement or signal pass through to another probe.
Color coded test wires with 2.54 mm (0.100 in) jumper connectors are included for direct connection to logic analyzers, multimeters, mixed signal oscilloscopes and debug adapters. Red and black test leads with 4 mm banana plugs connect directly to multimeters, bench power supplies and other instruments with standard 4 mm inputs.
Designed for DC to 10 MHz measurements and well suited for I2C, I3C, UART, CAN bus and other digital signals.
A PCBite base plate and holders are required.
Included
- 4x SP10 probe with spring tipped test needle (black)
- 4x SP probe holder for handsfree measurement
- 2x Banana to Dupont test lead (red, black)
- 5x Dupont test lead 80 cm (31 in), 5 colors
- 4x Extra test needle (SP/SQ)
Specifications
- Measurement range: DC to 10 MHz
- Needle resistance: below 0.02 Ω
- Current: up to 2 A continuous
- Test lead length: 80 cm (31 in)
- Package: 225 × 150 × 25 mm, 320 g
4005
CHF 69.00
excl. VAT
Description
Sensepeek PCBITE-4005 – 4x SP10 probes with test wires
These four handsfree SP10 probes expand your existing PCBite setup. Position each probe on the signals you need and monitor them with your logic analyzer, multimeter or debug adapter while keeping both hands free.
Place the spring-loaded needle on any test point in the signal path and release. The flexible arm holds the needle in position, while the N52 neodymium magnet in the base keeps the probe locked to the base plate. No soldered wires and no fixtures.
The 2.54 mm (0.100 in) dual pin header accepts two cables at the same time, enabling simultaneous power and measurement or signal pass through to another probe.
Color coded test wires with 2.54 mm (0.100 in) jumper connectors are included for direct connection to logic analyzers, multimeters, mixed signal oscilloscopes and debug adapters. Red and black test leads with 4 mm banana plugs connect directly to multimeters, bench power supplies and other instruments with standard 4 mm inputs.
Designed for DC to 10 MHz measurements and well suited for I2C, I3C, UART, CAN bus and other digital signals.
A PCBite base plate and holders are required.
Included
Specifications
Additional information
Handsfree DMM / Logic Probe
10
Debug Adapters, Logic Analyzers, Multimeters
Handsfree Probing
Available Technical Documents
Related Products
4004
CHF 7.00excl. VAT
Eight yellow insulation washers and four bottom caps for PCBite holders and handsfree probes. Replace worn parts and keep the setup sliding smoothly and insulated.
4017
CHF 8.00excl. VAT
Polycarbonate insulation cover for the PCBite L base plate, 297 × 210 mm (11.69 × 8.27 in, A4). Protects powered PCBs and reduces glare under the microscope.
4020
CHF 59.00excl. VAT
3× magnifier with an edgeless, anti-reflection coated lens and a magnetic base for any PCBite base plate. Tilt and rotation hold their position without set screws.